How to send the Data from Qt App to Arduino by serial communication

sankarapandiyan

@JonB said in How to send the Data from Qt App to Arduino by serial communication:

You still have not shown code which checks the result from serial->open(QIODevice::ReadWrite);.

YEs i have shown in above reply

sankarapandiyan

@Yunus Sure thanks a lot i will refer

JonB

@sankarapandiyan
You cannot expect people to help if you show output which simply does not correspond to anywhere in the code you have shown, can you? For example, you have a screenshot showing output where the code you have shown simply does not include any such output lines....

sankarapandiyan

@JonB ok fine.. thanks

ODБOï

@JonB said in How to send the Data from Qt App to Arduino by serial communication:

you have a screenshot showing output where the code you have shown simply does not include any such output lines..

hi, the 2nd line in his on_send_clicked method doas qDebbug() << "serial opened-"

@sankarapandiyan you should put it in a if statement to call qDebug only if open() returns true

if(serial->open(QIODevice::ReadWrite))

JonB

@LeLev said in How to send the Data from Qt App to Arduino by serial communication:

hi, the 2nd line ot his on_send_clicked method doas qDebbug() << "serial opened-"

You are right. I searched the whole page for serial opened (or even seral opened), I have only just seen it is in a screenshot. However, I still do not see where the baToSend used there is declared or set, I only see it elsewhere (local variable inside on_send_clicked()). Nor do I know what it is the text file read in. So it's still pretty hard to know what is going on....

sankarapandiyan

@JonB In text file i have 5 lines ,

line 1
line 2
line 3
line 4
line 5

i want to print these five line in arduino serial monitor , While i clicking send button

sankarapandiyan

@JonB Tried to Edit my code in correct form

#include "mainwindow.h"
#include "ui_mainwindow.h"
#include <QList>
#include <QComboBox>
#include <QString>
#include <QTextEdit>
#include <QTime>
#include <QDebug>
#include <QtSerialPort/QSerialPortInfo>
#include <QtSerialPort>
#include <QFile>
#include <QList>
#include <QSerialPort>

MainWindow::MainWindow(QWidget *parent)
    : QMainWindow(parent)
    , ui(new Ui::MainWindow)
{

      ui->setupUi(this);
      QString filename1="/home/adx-soft1/Shankar/serial/myfile1.txt";
      QFile file(filename1);
      if(!file.exists()){
          qDebug() << "NO FILE "<<filename1;
      }else{
          qDebug() << filename1<<" ...";
      }
      QString line1;
      ui->sender->clear();
      if (file.open(QIODevice::ReadOnly | QIODevice::Text)){ ui->sender->setText(file.readAll()); }

      QList<QSerialPortInfo> list;
      list = QSerialPortInfo::availablePorts();

      for (int i= 0; i < list.length(); i++)
      {
        ui->comboBox->addItem(list[i].portName());

      }
}

MainWindow::~MainWindow()
{
    serial->close();
    delete ui;
}

void MainWindow::on_pushButton_clicked()
{
    serial = new QSerialPort(this);
    serial->setPortName(ui->comboBox->currentText());
    serial->setBaudRate(QSerialPort::Baud9600);
    serial->setDataBits(QSerialPort::Data8);
    serial->setParity(QSerialPort::NoParity);
    serial->setStopBits(QSerialPort::OneStop);
    serial->setFlowControl(QSerialPort::NoFlowControl);
    serial->open(QIODevice::ReadWrite);
    connect(serial, &QSerialPort::readyRead, this, &MainWindow::serialReceived);

   ui->progressBar->setValue(100);
//    ui->receive->clear();
}
void MainWindow::checkAndSendData()
{
    if(!m_lines.isEmpty()){
        baToSend = m_lines.takeFirst().toUtf8();
        serial->write(baToSend);
        //qDebug() << baToSend << "serial Writed---" ;

        ui->aknowmnt->setText("Sent Message -->" +  QString(baToSend) + "\n");
    }
    else
    {
        ui->aknowmnt->setText("Receiving ");
    }
}


void MainWindow ::on_send_clicked()
{
      //serial->open(QIODevice::ReadWrite);
      qDebug () << baToSend << "seral opened ----" ;

      qDebug() << "Serial: " << serial->isOpen();
      qDebug() << "Error: " << serial->error() << " | " << serial->errorString();

      line = ui->sender->toPlainText();
        QString txt1 = ui->receive->toPlainText();
        /*QString*/ txt3 = ui->aknowmnt->toPlainText();

        qDebug() << "m_lines: " << m_lines;

         if(m_lines.isEmpty()){
            QFile inputFile(QString("/home/adx-soft1/Shankar/serial/myfile1.txt"));
            inputFile.open(QIODevice::ReadOnly);

            if (!inputFile.isOpen()) {
                return;
            }

            QTextStream stream(&inputFile);

            while(!stream.atEnd()) {
                QString strline = stream.readLine();
                m_lines.append(strline + QString("\r\n"));

                qDebug() << "m_lines: " << m_lines;
            }
        }
        checkAndSendData();
}


void MainWindow::serialReceived()
{

    qDebug() << "serial->readAll().trimmed(): " << serial->readAll().trimmed();

    QString glen = serial->readAll().trimmed();

    qDebug() << "glen: " << glen;

     if (glen.length() > 0) {
         ui->receive->append(glen);
        /*QString*/ //line = ui->receive->toPlainText();
        //ui->receive->setText(ui->receive->toPlainText() + line + "\n");
        //ui->receive->setText(line + "\r\n" + glen + "\r\n");
        //line = txt3;
    }
    checkAndSendData();
}

But i did not get the data received in arduino side

sankarapandiyan

@LeLev ok fine i will correct it

sankarapandiyan

@JonB @LeLev @mrjj cant open port : QSerialPort::SerialPortError(PermissionError)
I get the error like this ..

Thanks

jsulm

@sankarapandiyan said in How to send the Data from Qt App to Arduino by serial communication:

PermissionError

Make sure your user has needed access rights for the serial port device file.
See for example https://askubuntu.com/questions/58119/changing-permissions-on-serial-port

sankarapandiyan

@jsulm Is it possible to open the port in both Qt app and Arduino in a same OS ..
Here if i open the port in Qt means , in Arduino ,i got a error the port is changed or not found

while if i open the port in Arduino first means , I got a error message in Qt as (PERMISSION ERROR)

I am Stucked here for a day, I am very new to this arduino topic , So give me some idea abouth this .

Thanks in advance .

jsulm

@sankarapandiyan said in How to send the Data from Qt App to Arduino by serial communication:

Is it possible to open the port in both Qt app and Arduino in a same OS

Not sure what you mean? If both devices run same OS then yes.

"i got a error the port is changed or not found" - then make sure you're using correct port!

"I got a error message in Qt as (PERMISSION ERROR)" - then make sure your user has access right like I suggested above.

JKSH

@sankarapandiyan said in How to send the Data from Qt App to Arduino by serial communication:

Is it possible to open the port in both Qt app and Arduino in a same OS ..

If you have 2 apps on the same computer that want to use the same serial port, then only one of the programs can use the serial port at a time.

When App 1 opens a serial port, App 2 cannot use the same serial port. App 2 must wait until App 1 closes the port.

Lemat

This post is deleted!

sankarapandiyan

@JKSH Yes You are right .. thanks for your reply

sankarapandiyan

@jsulm sure