serial Communication using Threading

[Vijaykarthikeyan]

@JonB Ok. I agree with you. I'm doing the wrong way. But,replacing timer with readyRead() signal throws the garbage..this is my 1st issue.If my code implementation is wrong..please correct me.

My aim is to send mavlink like struct data from one device to my device.For that,the 1st byte should be the magic number(in this case, I have used 253(0xFD in hexadecimal)).If and only if matches, it reads through the remaining bytes which is the size of my struct. We can't send/receive struct data type through serial port.That's Why Im using QByteArray.

So,as far as your suggestion, How to cumulate the data? I know this issue is out of text thing which I have asked . Im ready to receive your coorrections

[jsulm]

@Vijaykarthikeyan said in serial Communication using Threading:

But,replacing timer with readyRead() signal throws the garbage

What does this mean? How does your code using readyRead() look like now? Do you accumulate the data?
You need to accumulate data you get every time readyRead() is emitted until you get a whole frame of data. Just like @SGaist and @JonB suggested.

[Vijaykarthikeyan]

@Vijaykarthikeyan said in serial Communication using Threading:

@jsulm When using ready read() signal..it throws the error like this:

Port opened
50.66 20.77 17.89
-4.21704e+37 9.11138e-41 1.95399e-13
-4.21704e+37 9.11138e-41 1.56319e-13
50.66 20.77 17.89
-4.21704e+37 -1.99953e+18 3.76588e-13

That's Why i choose timer for receiving data

Already said that corrections are welcomed.. thank you

[jsulm]

@Vijaykarthikeyan said in serial Communication using Threading:

Already said that corrections are welcomed

Corrections? Do you expect somebody to write correct code for you?
You got the suggestion to use readyRead(), accumulate the data and parse it according to the protocol - did you do that? You do not even answer questions...

[Vijaykarthikeyan]

@jsulm on using readyRead() it throws the garbage values in the middle of incoming serial port values,,that's what im mentioning in every thread.

I didn't tell anyone to write the code for me.. and why I should? I have implemented the method without seeing into any examples and it worked for me? My Question is now gone nowhere. The topic is changed? The actual defintion of correction is not writing the code behalf of me.

[jsulm]

@Vijaykarthikeyan said in serial Communication using Threading:

on using readyRead() it throws the garbage values in the middle of incoming serial port values

It was already asked before: show your current implementation. How else should anybody know why it does not work? We do not know whether you're accumulating the data correctly and we do not know whether you're parsing accumulated data correctly.

[J.Hilk]

@jsulm @Vijaykarthikeyan and wether you're printing it correctly, simply dumping it into qDebug() will probably lead to "chunk" data interpretation.

also

memcpy(&receivedStruct, receivedData2+receivedData.constData(), sizeof(MyStruct));

I somehow doubt you're familiar with packing rules and restrictions. I would suggest ditching C and giving your Struct an constructor overload that accepts a QByteArray or a QDataStream implementation or simply overload <<

[Vijaykarthikeyan]

@J-Hilk Thank you,Sir you are correct. it has to be correctly packed to avoid those conditions. I Pre-determinely know the Struct size.And that helped me to pack the struct from extracting the stream input based on the size.

[Vijaykarthikeyan]

@jsulm ```
#include "mainwindow.h"
#include <QThread>
#include <thread>

MainWindow::MainWindow(QWidget *parent)
: QMainWindow(parent)
{
serial = new QSerialPort(this);
serial->setPortName("COM7");
serial->setBaudRate(QSerialPort::Baud115200);
serial->setDataBits(QSerialPort::Data8);
serial->setParity(QSerialPort::NoParity);
serial->setStopBits(QSerialPort::OneStop);
serial->setFlowControl(QSerialPort::NoFlowControl);

if (serial->open(QIODevice::ReadWrite))
{
    qDebug() << "Port opened";

    QThread::msleep(1000);
    timer = new QTimer(this);
    connect(timer, &QTimer::timeout, this, &MainWindow::send_data);
    connect(serial, &QSerialPort::readyRead, this, &MainWindow::read_data);
    timer->start(500);

}
else
{
    qDebug() << "Port not opened";
}

}

MainWindow::~MainWindow()
{

}

void MainWindow::send_data()
{

//QByteArray *sendData = new QByteArray();
    MyStruct sendStruct ;
    AHRS ahrs_data;
    ahrs_data.yaw =50.66;
    ahrs_data.pitch=20.77;
    ahrs_data.roll=17.89;

    memcpy(sendStruct.payload, &ahrs_data, sizeof(AHRS));
    sendStruct.magic=0xFD;
    sendStruct.length=sizeof(AHRS);
    sendStruct.sequence=1;
    sendStruct.sysId=1;
    sendStruct.compId=2;
    sendStruct.msgId=1;

    //sendData->append(reinterpret_cast<const char*>(&sendStruct), sizeof(MyStruct));
    serial->write(reinterpret_cast<const char*>(&sendStruct), sizeof(MyStruct));

    //delete sendData;

}

void MainWindow::read_data()
{
if(serial->bytesAvailable())
{
QByteArray receivedData,receivedData2;
MyStruct receivedStruct ;
receivedData2 = serial->read(1);

    if(receivedData2.contains(253))
    {

        receivedData = serial->read(sizeof(MyStruct)-1);
        memcpy(&receivedStruct, receivedData2+receivedData.constData(), sizeof(MyStruct));
        AHRS ahrs_data;
        memcpy(&ahrs_data,receivedStruct.payload,sizeof(AHRS));
        qDebug()<<ahrs_data.yaw<<"\t"<<ahrs_data.pitch<<"\t"<<ahrs_data.roll;

    }

    else
    {
    }

    }

}

[jsulm]

@Vijaykarthikeyan said in serial Communication using Threading:

receivedData = serial->read(sizeof(MyStruct)-1);

I think the problem here is that it can happen that you will not receive the whole struct at once. That's why it was suggested to accumulate received data until you have enough data to extract the whole struct.

[Vijaykarthikeyan]

@jsulm ok..I understand. I'll try. If any issue occurs..I'll post that error. Thank you

[craxedunt]

This post is deleted!