i cannot check my QPushbutton that is in my qtableview

aftalib

so C++ lambda might be the way to relate to each of the QPushButtons i created with my loop ?

JonB

@aftalib
You will need the lambda when you are ready to have the single slot code method handle the clicking of any of the push buttons, which I suspect is what you will want to achieve.

However, before you do that, put a qDebug() << "clicked" in as the first statement in the slot. Verify that gets called when any of the buttons you created are clicked, not just one button. Only at that point are you ready to move to a lambda for the slot which will pass which button was pressed as a parameter to the slot....

aftalib

@JonB okay, the slot gets called of any of the buttons i have created, i have the "clicked" output on each of the buttons

JonB

@aftalib
And have you used the new style syntax I referred you to earlier? Show your connect() statement now.

aftalib

@JonB i dont think i got it right.. the IDE still says that clicked() is an undeclared identifier..

JonB

@aftalib
I said to you earlier:

You have to read and act on https://wiki.qt.io/New_Signal_Slot_Syntax.

but you do not seem to have done anything about this....

aftalib

@JonB no i did check this in order to do the new connect statement but i dont get how am i supposed to write this with what is written on this page

jsulm

@aftalib Please post text not screen shots.

connect(H11, &QPushButton::clicked, this, &WHAT_EVER_THIS_TYPE_IS::on_H11_clicked);

JonB

@aftalib
The very first section there shows an example of changing from SIGNAL/SLOT() macros

connect(
    sender, SIGNAL( valueChanged( QString, QString ) ),
    receiver, SLOT( updateValue( QString ) )
);

over to

connect(
    sender, &Sender::valueChanged,
    receiver, &Receiver::updateValue
);

The code you have pasted does not attempt to follow that required pattern.

aftalib

okay thats my bad i didnt quite understand the syntax that was written in the new connect statement but i think i got it now, thank you. here's what i wrote :

         connect(H11, &QPushButton::clicked,this,&AntArrayDialog::on_H11_clicked);

i dont get any errors and the program launches well

aftalib

then i have to use lambda with this syntax in order for my slot to work with any of the buttons i created right?

JonB

@aftalib
Yes, this is good :)

Now, I believe, since (I assume) you will have each of the buttons connect to this one slot method, you will want the slot to receive a parameter to tell it which particular button was clicked this time to call the slot, right?

To do that you are going to need to move on to connect()ing a C++ lambda instead of the slot function as you currently do now. Then a parameter can be added, so that the signal will pass it to the slot. the parameter will identify which button emitted the signal.

That new-style syntax page includes the following example:

Can be used with C++11 lambda expressions:

connect(
    sender, &Sender::valueChanged,
    [=]( const QString &newValue ) { receiver->updateValue( "senderValue", newValue ); }
);

The lambda bit is:

[...](...) { ... }

See if you can figure how to pass the QPushButton * object from the signalling push button to the slot....

aftalib

@JonB okay, just before you answered i tried this :

connect(H11, &QPushButton::clicked,[this](){

             if (H11->isChecked()) {

                 H11->setText("H2");
                 qDebug() << "test";
             }

             else if (H11->isChecked()==false){
                 H11->setText("H1");


             }

         });

so if i click on any button i want it to change to H2, then to H1 if i reclick on it and so on..
i didnt get any errors but it didnt work so im assuming this is wrong. im gonna retry something else with what you said

JonB

@aftalib
At least you have you lambda syntax correct, that is good!

Your connect() is not attempting to pass which button was clicked, as a parameter to the slot. The slot only references whatever one button this->H11 currently refers to when it is executed. If you are wanting the slot to know which button invoked it in order to do its work, you are going to need that as a parameter to the slot in the lambda.

aftalib

@JonB said in i cannot check my QPushbutton that is in my qtableview:

okay i get what you're saying, so i need to put the button that is calling the slot as a parameter. here's what i tried but its not working either :

 connect(H11, &QPushButton::clicked,[=](QPushButton &button){

             if (button.isChecked()) {

                 button.setText("H2");
                 qDebug() << "test";
             }

             else if (button.isChecked()==false){
                button.setText("H1");


             }

         });

i know that its almost the right thing but im missing something

aftalib

so i've spent most of the last night searching for a solution to this but still havent found. does anyone have an idea about this ?

thank you in advance

JonB

@aftalib
One way, briefly, untested:

connect(button1, &QPushButton::clicked, [=, button1]() { pushbutton_clicked(button1); }
connect(button2, &QPushButton::clicked, [=, button2]() { pushbutton_clicked(button2); }
for (auto button : each_button_when_created)
    connect(button, &QPushButton::clicked, [=, button]() { pushbutton_clicked(button); }

void ThisClass::pushbutton_clicked(QPushButton &button)
{
    // now button parameter is whichever button clicked
    // so you can use this for stuff you want to do on any of the buttons
    if (button.isChecked())
        ...
}

aftalib

okay i can see this working, so i have to put the numbers of buttons i want in the line "for (auto button : each_button_when_created" ? i dont get how this line works

aftalib

i just checked how the for auto loop works. would it help if i created an array of buttons in order for this to run ?

JonB

@aftalib
Yes, but you are taking the code too literally. It doesn't matter whether you use a for on an array of buttons or whatever. In your original code I believe you have some loop which creates QPushButtons dynamically --- I assume/was assuming you create one per each some column in your QTableView? Anyway that loop is there to show you that you can connect() any time you have a dynamic pushbutton to link up, wherever it coms from, or individual button variables button1/2 if that's what you have.