Solved Building an app based on a dev (manual) build of Qt
-
Hi,
I built Qt 5.15.3 from git using the manual on the website and set up a kit in developer mode. Now, I want to build an app using my manual Qt build instead of the system/Online installer version. For the online installer version, I useDCMAKE_PREFIX_PATH=/home/teecee/Qt/5.15.2/gcc_64
, which worked just fine. However, I am unable to do the same with my manual Qt installation. I added the top level directory of both qt5 and qt5-build, but both aren't recognized. Then I tried/home/teecee/qt5-build/qtbase/lib/cmake/Qt5/Qt5Config.cmake
, which also failed. Is there any solution for this problem? -
Sorry to post it so late, but I built it again without
developer-build
, and now adding the path to the explicit install directory somewhat solved my problem. -
@tcee_14007 Where did you install your Qt build (make install)
-
I ran the command in the build folder itself
-
@tcee_14007 But where did "make install" install it?
-
I'm sorry, but I'm unable to find it.
However, I have attached the bash output here: https://pastebin.com/Y4ZEVtDr
could you please take a look at it ? -
It seems like what was pasted into pastebin was from a subsequent (not original) run of "make install". There is a bunch of output like "Nothing to be done", which indicates that things were already installed. During an initial run I would expect to see a bunch of
cp
action showing things being copied to some destination.Unless you, @tcee_14007 explicitly used the
-prefix
argument when you ranconfigure
, then things probably installed to a system folder.If you run
./configure --help
you should see what the default prefix is.On my system, it shows:
-prefix <dir> ...... The deployment directory, as seen on the target device. [/usr/local/Qt-$QT_VERSION; qtbase build directory if -developer-build]
If you think that the
-prefix
argument was used, then look at theconfig.log
file (wherever you ran configure & make) and you should be able to retrieve the arguments fromconfig.log
(try searching the log for the phrase "Command line") -
I had added -developer-build to the configure command, and it said that I shouldn't run make install. I ran it for the first time after @jsulm asked me to, so the problem might be different. And I checked, I didn't add -prefix.
-
Interesting!
I had never paid any attention to that option. (although I now see that in the snippet of help text I posted for
prefix
earlier, there is a mention ofdeveloper-build
, too!)I found this mailing list entry "What does '-developer-build' actually do":
https://lists.qt-project.org/pipermail/qt-interest-old/2010-April/021593.htmlAs @jsulm has already highlighted, the key thing is still to figure out where on earth your manually-compiled binaries got "installed" to.
For
developer-build
they are supposedly in$PWD
(of wherever you ranmake
, I guess)?Maybe just try to find where it put
qmake
:cd $WHEREVER_YOU_PUT_YOUR_MANUAL_QT_STUFF find . -type f -name qmake
-
When I say that I have never paid attention to
developer-build
, I suppose I should be explicit about what I normally do do.I often build debug versions of Qt, and occasionally even experiment with editing the source and rebuilding with my changes included.
When I do that I simply run
configure
with the-prefix
argument pointing at some special folder that won't pollute my global/usr/
or/usr/local
areas.And of course I add the
-debug
flag so that I get debug symbols.When using
-prefix
and thenmake && make install
, the ultimate installation location is controlled by whatever I chose to specify asprefix
.This isn't necessarily better than using
developer-build
!!Just explaining how those of us who were ignorant of
developer-build
have been doing this ;) -
Sorry to post it so late, but I built it again without
developer-build
, and now adding the path to the explicit install directory somewhat solved my problem. -
@tcee_14007 said in Building an app based on a dev (manual) build of Qt:
Sorry to post it so late, but I built it again without
developer-build
, and now adding the path to the explicit install directory somewhat solved my problem.I don't think you are posting late :)
There was no deadline. I'm glad to hear back about what worked.
Maybe someone who knows more about
developer-build
can comment about how to successfully useDCMAKE_PREFIX_PATH
with a Qt "install" that was created withdeveloper-build
. -
Hi,
The developer-build option is for people wanting to hack on Qt itself so it should not be used for deployment purpose nor development other than Qt itself. IIRC, there are some difference in the set of options and flags used for the compilers.
It's an "in-place" build so there's nothing to install.
-
This post is deleted!