QT Creator hangs on opening a file or project

mrjj

@dashthird
reboot
Then just try to run Creator.
(i pray for a bit of luck)

hskoglund

To add to @mrjj, in case the uninstallation of AVG didn't help, there's one more thing you could try, start a CMD window, type set path= to clear the path and then in that same CMD try start Qt Creator manually, eg:

set path=
C:\qt\tools\qtcreator\bin\qtcreator.exe

If you can Browse for project folder location now, then there's something spooky in your path settings. However, when starting Qt Creator this way, you will most likely not be able to compile from inside Qt Creator :-(

dashthird

@mrjj
Even after AVG uninstall + reboot, the issue is still there :(

dashthird

@hskoglund
Tried your method also, set the path & also ran the QTCreator from CMD.
Still then, on "File->Open project/file", the issue is same :(

I would record a small video of the same & post it here

hskoglund

Ok one more : try disconnect from internet, pull out the wire or disconnect the WiFi

dashthird

@hskoglund Even after disconnecting from the internet, the issue is same

@hskoglund @mrjj Please find the video link attached

QTIssue.avi

hskoglund

Hi, saw the video, 2 things you can try:

try reinstalling Qt 5.6.1 on C: (not E:)
go to Control Panel and create a new user, log out and log in as that new user, then try Qt Creator

dashthird

@hskoglund The issue is still the same!

mrjj

@dashthird
so even with new user, and Qt install on C:
it still does it ?
(OMG)

hskoglund

Oh, forgot one thing you can test: open a CMD window and start Qt Creator with 2 switches, like this:

C:\qt\Tools\QtCreator\bin\qtcreator.exe -noload all -load Core

You will have a stripped down UI but Open File or Project is still present...

dashthird

@mrjj

I had tried 2 approaches:
created a new user "test"

in new user, simply tried opening QT Creator of E:(installed by old user) & then "File->Open project/file"
Still the same issue
in old user, deleted the QT from E:
in new user, installed QT at C: & then "File->Open project/file"
Still the same issue

@hskoglund
Would try your latest CMD method & would let you know the output

dashthird

@hskoglund
Yes, Yes, I am able to see the Open Project/file window when I open from CMD using:

C:\Qt\Qt5.6.1\Tools\QtCreator\bin\qtcreator.exe -noload all -load Core

Here's the screenshot:

:)

Where do you think is the cause?

hskoglund

So most likely some Qt Creator plugin is the culprit.
To find which one(s), start Qt Creator (you can start it normally), open the Help\About Plugins dialog box.

Try deselecting (making the plugin not Load) some of the plugins, try first with all the plugins listed under Utilities. Then exit Qt Creator, start it again and try Open File or Project and see if it hangs. If it still hangs, try deselecting more plugins. If it does not hang, then try selecting a few plugins to see which one is the bad boy :-)

JonB

@hskoglund
Would this be a case where the user should set

set QT_DEBUG_PLUGINS=1

in CMD before running qtcreator.exe and see if it reveals any plugin problem or suspect?

hskoglund

@JonB Might be, but the hang does not occur when launching Qt Creator, but when selecting Open File or Project, and by that time most of the plugins are already loaded.

JonB

@hskoglund
Yes, I have no idea, I was hoping with QT_DEBUG_PLUGINS they might speak up as they were called to do something and give a clue as to what was happening :)

hskoglund

@JonB QT_DEBUG_PLUGINS will cause qDebug() outputs from the likes of qpluginloader.cpp and qlibrary.cpp but a normal plugin I think is an ignoramus re. that env. variable.

But having a dbgview running before trying that Open File or Project hanging stunt can be a good idea, since there might be a qWarning issued in there somewhere...

dashthird

@hskoglund
The culprit is the "Welcome" plugin (of "QT Creator" section)
On disabling that, I am now able to do "File->Open file/project" :-)

Now the starting QT UI seems a lot similar like the QT SDK 1.2.1 (maintained by Nokia), which I was using before upgradation to QT 5+ version.

Thanks a lot!!!
I can finally start coding in C++ now :)

One last question: Is there any alternate way to enable the functionality of that "Welcome" plugin ?

hskoglund

Hmm don't know any alternate way, you'll have no "Welcome" icon on the left sidebar, but you can use the File menu to create new projects and load existing ones. And browse the Qt Examples manually using File Explorer.

And F1 context help still works in the editor etc so you'll survive I think :-)

Edit: just realized, you're not using a recent Qt Creator (version right now is 4.12.3)?
Some years ago, the Welcome plugin in those old Qt Creator versions relied on OpenGL functionality, so it was a common cure to disable it like you did today (just google for "Qt Creator Welcome plugin problem")
The Welcome plugin was rewritten to not rely on OpenGL, maybe 3 years ago? So you could try update your Qt Creator and re-enable the Welcome plugin...

dashthird

@hskoglund
Okay, would try that.

I had actually downloaded a single all-in-one installation package qt-opensource-windows-x86-mingw492-5.6.1-1.exe

I had not edited any QTCreator version in that. The QT Creator 4.0.1 is bundled with v 5.6.1, so may be the latest Creator v4.12.3 is bundled with v5.15. Would check that also

Thanks a lot!
Have marked your answer as the solution :)