What is the difference between Run and Debug in QtCreator?

[Pauly]

@VRonin said in What is the difference between Run and Debug in QtCreator?:

data.lpData = dataString;

I'm getting a bunch of errors. What should I do?

191: error: assignment of read-only location '*(dataString + ((sizetype)(((unsigned int)i) * 2u)))'
dataString[i] = static_cast<TCHAR>(cmd.at(i).unicode());
^

192: error: assignment of read-only location '(dataString + ((sizetype)(((unsigned int)cmd.QString::size()) * 2u)))'
dataString[cmd.size()]=static_cast<TCHAR>('\0');
^
error: invalid conversion from 'const void' to 'PVOID {aka void*}' [-fpermissive]
data.lpData = dataString;
^

[VRonin]

sorry, didn't realise LPCTSTR (I too failed at reading hungarian notation) is defined as const, just replace it with LPTSTR or with TCHAR* or with auto

[Pauly]

@VRonin said in What is the difference between Run and Debug in QtCreator?:

sorry, didn't realise LPCTSTR (I too failed at reading hungarian notation) is defined as const, just replace it with LPTSTR or with TCHAR* or with auto

Thanks for the note. So I change the code to:

TCHAR* dataString = new TCHAR [cmd.size()+1];
for(int i=0; i<cmd.size();++i)
    dataString[i] = static_cast<TCHAR>(cmd.at(i).unicode());
dataString[cmd.size()]=static_cast<TCHAR>('\0');


COPYDATASTRUCT data;
data.dwData = MAGIC;
data.cbData = cmd.size()+1;
data.lpData = dataString;
char* a=(char *)data.lpData;

for (int i=0; i<data.cbData; ++i) {
    qDebug() << *a ;
    ++a;
}
DWORD lpdwResult;
LRESULT err = SendMessageTimeout(hwnd, WM_COPYDATA, 0, (LPARAM)&data, SMTO_ABORTIFHUNG, 2000, &lpdwResult); //WM_COPYDATA

I can see the cmd being printed out (only half of cmd thought) but debug mode still failed. Target application now seems to get the first character of cmd, just as if I send QString* or QString.toLatin1().data().

I guess the question comes down to, what is the difference in QString::toLocal8bit().data() in Run mode and Debug mode?

[VRonin]

@Pauly said in What is the difference between Run and Debug in QtCreator?:

char* a=(char *)data.lpData;

Are you sure lpData is char and not wchar?

instead of

char* a=(char *)data.lpData;

for (int i=0; i<data.cbData; ++i) {
    qDebug() << *a ;
    ++a;
}

try printing it using

#if defined(UNICODE) || defined(_UNICODE)
std::wcout
#else
std::cout
#endif
<< static_cast<TCHAR*>(data.lpData);

what is the difference in QString::toLocal8bit().data() in Run mode and Debug mode?

QString::toLocal8bit() returns a temporary QByteArray, .data() returns a pointer to the internal data of that temporary variable. That pointer becomes invalid as soon as the temporary variable gets destroyed (i.e. a line below). The debug mode might just keep that variable alive for longer lo let you see inside it if you needed to

[Pauly]

@VRonin

Where could I see the output as printing it your way? I'm running this at QtCreator and I can't figure out where the output goes. Thanks.

[jsulm]

@Pauly "Application output" tab

[Pauly]

@jsulm

I see that now. Yes, it is the cmd that I'm trying to send. However the application still does not get it...

[VRonin]

How does the application expect the command? UTF-16, UTF-8, ASCII?

[Pauly]

I think UTF8, since .toLocal8bit() is the only thing that works, even in Run mode...

[VRonin]

ok then, back to the basic:

void MyClass::SendCmd(HWND hwnd, QString cmd)
{
const QByteArray utf8Cmd = cmd.toUtf8();
COPYDATASTRUCT data;
data.dwData = 0x267811;
data.cbData = cmd.size()+1;
data.lpData = utf8Cmd.data();
DWORD lpdwResult;
LRESULT err = SendMessageTimeout(hwnd, WM_COPYDATA, 0, (LPARAM)&data, SMTO_ABORTIFHUNG, 2000, &lpdwResult); //WM_COPYDATA
}

@Pauly said in What is the difference between Run and Debug in QtCreator?:

I think UTF8, since .toLocal8bit() is the only thing that works

toLocal8bit not necessarily == toUtf8