X11/Xlib.h: No such file or directory

marvic_39

Ok. But, Same setup worked for other ARM device and able to compile apps.

Why it is not working for this device? Installed the dependencies.

SGaist

Without any details about your device/linux distribution it's pretty much Crystal Ball Debugging. As to why its working for other devices: what is different between these other devices and this one ?

marvic_39

@SGaist

Sorry, i have not mentioned it.

I am not compiling on target board directly. Cross compiling using Linaro tool chains for Odroid XU4.

Took this source code qt-everywhere-opensource-src-5.2.0
For BeagalBone "-qt-xcb" option in configure worked without any error and build created. qmake worked fine in QtCreator.

For Odroid XU4 "-qt-xcb" option in configure flashing error

**X11/Xlib.h: No such file or directory**

If it is -no-xcb this will get compiled and build created without that error.
Even if i do not give xcb option in configure it compiles and builds the code.

So, how to build for Odroid XU4 with xcb support.

SGaist

You have to add the needed Xorg dev packages to your Odroid sysroot

marvic_39

@SGaist

Well, i am not using sysroot. Instead , Using -prefix option so that all that make install stuff goes to /usr/local/qt-5.2-odroid.

Created a folder in /home/odroid, Did the configure with below options,

../qt-everywhere-opensource-src-5.2.0/configure -v -opensource -confirm-license
-prefix /usr/local/qt-5.2-odroid -no-largefile -no-accessibility -qt-zlib -no-gif -qt-libpng 
-qt-libjpeg -no-nis -no-cups -xplatform linux-arm-linaro-gnueabihf-g++ -device linux-
odroid-xu4-g++ -device-option CROSS_COMPILE=/usr/local/linaro/bin/arm-linux-
gnueabihf- -no-xcb -no-c++11 -no-pch -nomake examples

This will build, with -no-xcb option.

From Qt Creator i will set the Compiler, Kit and qmake. Just build and deploy.
And it worked well on Odroid XU4

How to get through with -qt-xcb option for Odroid.
For BeagalBone it works with -qt-xcb option.

SGaist

Then you have to provide all missing headers and libraries in your cross-compiler folders

marvic_39

@SGaist

Yes, i copied all the required headers to that folder. Set PATH to that folder also.
Still it's flashing error.

For beagalbone, it compiled properly. How did that .conf file searched the files.

Wjy Odroid .conf is not ? Any thing to be done for PATH setting

SGaist

You didn't provide the libraries.

When cross-compiling, the compiler and linkers need to be able to access both the headers and corresponding libraries for the device or at least the architecture your are building for. These are usually provided in the sysroot of your device along with specific stuff to access e.g. the GPU so that you are building against the same set of libraries you'll be using for your device.

Since you don't want to use the sysroot of your device, then you have to add everything by hand for your cross-toolchain to find.

marvic_39

@SGaist

I understood about that, but

For beagalbone ( Without sysroot ), build created and linked all libraries automaticall, i have not added any headers or libraries manully. This toolchain(Angstrom) having all the headers and correct paths.

Same thing should go with Odroid?
I am using this tool chain gcc-linaro-arm-linux-gnueabihf-4.8-2014.04_linux to build Qt on Odroid. And this toolchains does not have few headers related xcb and others. Manually i added some. Libraries not located after searching.

Any specific tool chains to build for Odroid XU4 .

If build is without xcb, what all the features will be missing?

SGaist

Because Angstrom is not just a toolchain, it's a distribution. gcc-linaro-arm-linux-gnueabihf-4.8-2014.04_linux is only a toolchain.

marvic_39

@SGaist

I could not find xlib libraries in the system, even after installing all the dependencies.

SGaist

How did you install the dependencies ?

marvic_39

@SGaist

sudo apt-get install libx11-dev libavahi-gobject-dev libSM-dev libfontconfig-dev
libXext-dev libfontconfig1-dev libfreetype6-dev libx11-dev libxcursor-dev
libxfixes-dev libxft-dev libxi-dev libxrandr-dev libxrender-dev

SGaist

These are for your host system not for your target.

marvic_39

@SGaist

Well, during building (configure) Qt on host this error is raised.
How target comes into picture?

SGaist

Since you want to cross-compile Qt with X11 support you need to provide your cross-toolchain with both header and libraries for the architecture you are cross-compiling to.

marvic_39

@SGaist

Ok, Where from i get libraries.

SGaist

2 solutions are possible:

Cross-compile each dependency needed
Get the packages from the distribution of your board, extract them somewhere and add the paths to your configure line.

marvic_39

@SGaist

OK,

Regarding first option,
Headers and their linking headers are many, it's becoming difficult to get exact files and even difficult to compile.

Regarding second option.
I could not find the distribution for Odroid, If you can provide me some links to download it.

Thank you.

SGaist

What linux flavor are you running on your Odroid ?