Function step by setp

Franckynos

Hi,

I use serial port to do something.

When I write :

void MainWindow::mouve()
{
    stepX->moveR(1000);
    stepX->moveR(-200);
    stepX->moveR(1000);
    stepX->moveR(-20000);
    stepX->moveR(100);
}

void StepperMotor::moveR(int step)
{
    QTimer t;
    t.setInterval(10000);
    int posReach = send(GAP,1,0,0) + step;
    send(MVP, 1, step, 0);
    t.start();
    while (posReach != send(GAP,1,0,0,false) && t.remainingTime()>0);
}

mouve is connected to button when I clik on it, funcitons are done setp by setp
stepX->moveR(-200); wait the end of stepX->moveR(1000);

The problem is th GUI Freez ... so I do this :

void MainWindow::mouveandwait() // connected to my button
{
    qDebug() << "Main Thread" << this->thread()->currentThread();
    QtConcurrent::run(this, &MainWindow::mouveth);
}

void MainWindow::mouveth()
{
    qDebug() <<"start" <<QTime::currentTime() << this->thread()->currentThread();
    stepX->moveR(1000);
    stepX->moveR(-200);
    stepX->moveR(1000);
    stepX->moveR(-20000);
    stepX->moveR(100);
    qDebug() <<"end" <<QTime::currentTime();
}

but now all function are executed
stepX->moveR(1000);
stepX->moveR(-200);
stepX->moveR(1000);
stepX->moveR(-20000);
stepX->moveR(100);

without waiting the end of previous.

All "stepX->mouveR" are in the same thread, diffrent of Main thread

Someone can help to do this step by setp?

I use some mutex but nothing change.

mrjj

@Franckynos said:
Hi
the
while (posReach != send(GAP,1,0,0,false) && t.remainingTime()>0);

is the reason GUI is hanging. U kill the message pump.

Im wondering what "send(GAP,1,0,0,false)" is.

Its that sending over serial?
If yes , You should look into signals as it can tell you when finished sending etc and you could design this step by step
in a way not using a loop.

So each step would send signal when finished and the slot would then start the next step.
Of Course if "send" is something completely different that serial port then might not be possible :)

Franckynos

For more detail,

int StepperMotor::send(int commande, int param, int value, int motor_bank, bool verbose)
{
    SendCmd(hRS232, 1, commande, param, motor_bank, value);
    while(GetResult(hRS232, &Address, &Status, &Value)==TMCL_RESULT_NOT_READY && abs(GetTickCount()-Timeout)<1000);
}

and SendCmd & GetResult are api window not Qt, because with Qt, the responding time is to long

void StepperMotor::SendCmd(HANDLE Handle, UCHAR Address, UCHAR Command, UCHAR Type, UCHAR Motor, INT Value)
{
    UCHAR TxBuffer[9];
    DWORD BytesWritten;
    int i;

    TxBuffer[0]=Address;
    TxBuffer[1]=Command;
    TxBuffer[2]=Type;
    TxBuffer[3]=Motor;
    TxBuffer[4]=Value >> 24;
    TxBuffer[5]=Value >> 16;
    TxBuffer[6]=Value >> 8;
    TxBuffer[7]=Value & 0xff;
    TxBuffer[8]=0;
    for(i=0; i<8; i++)
        TxBuffer[8]+=TxBuffer[i];

    //Send the datagram
    WriteFile(Handle, TxBuffer, 9, &BytesWritten, NULL);
}

UCHAR StepperMotor::GetResult(HANDLE Handle, UCHAR *Address, UCHAR *Status, int *Value)
{
    UCHAR RxBuffer[9], Checksum;
    DWORD Errors, BytesRead;
    COMSTAT ComStat;
    int i;

    //Check if enough bytes can be read
    ClearCommError(Handle, &Errors, &ComStat);
    if(ComStat.cbInQue>8)
    {
        //Receive
        ReadFile(Handle, RxBuffer, 9, &BytesRead, NULL);

        Checksum=0;
        for(i=0; i<8; i++)
            Checksum+=RxBuffer[i];

        if(Checksum!=RxBuffer[8]) return TMCL_RESULT_CHECKSUM_ERROR;

        *Address=RxBuffer[0];
        *Status=RxBuffer[2];
        *Value=(RxBuffer[4] << 24) | (RxBuffer[5] << 16) | (RxBuffer[6] << 8) | RxBuffer[7];
    } else return TMCL_RESULT_NOT_READY;

    return TMCL_RESULT_OK;
}

When I put this code :

void MainWindow::mouveth()
{
    qDebug() <<"start" <<QTime::currentTime() << this->thread()->currentThread();
    stepX->moveR(1000);
    stepX->moveR(-200);
    stepX->moveR(1000);
    stepX->moveR(-20000);
    stepX->moveR(100);
    qDebug() <<"end" <<QTime::currentTime();
}

In a Thread (QtConcurrent) all function are done without waiting the previous. How can I wait in thread ?

Thx for reply

mrjj

hi
if look at the sample
http://doc.qt.io/qt-5/qtconcurrent-progressdialog-example.html

you can see how to use futureWatcher
QObject::connect(&futureWatcher, SIGNAL(finished()), &dialog, SLOT(reset()));
to be notified when a thread is finished.

I think you should use this method to run a step and when it signal Finished, you run next step and so on.

I do not know a way to make it pause in each
when you run them all in one thread at once.
Maybe other will :)

Hope it help