[Solved]QSerialPortInfo::availablePorts() does not work. Can not enumerate serial ports
-
bq. QSerialPortInfo shouldn`t find my usb ports?
It should work fine.
bq. And I need platform`s. Because maybe I need create virtual port.
Here need to do modifications in source code.
-
Then please do
bq. $udevadm info --name=/dev/ttyXYZ -a
where ttyXYZ - name of your USB device and give print out.
-
Sorry?
[quote]I print it in this thread already at above.[/quote]
That you printed is not belongs to the USB devices.[quote]
I mean from USB device like mouse.
I say QPortSerailInfo should not list these usb ports? e.g mouse
[/quote]
Mouse is not an serial port's device (not an tty device). The QSeralPortInfo works only with the serial port's devices. But in case your mouse will be present in system as serial device (with the appropriate driver) - then QSeralPortInfo will work with this. -
Thank you for helping me.
You say USB mouse is not a serial port?
I run a virtual serial port using socat and again QSerialPortInfo did not find.
Maybe I have problem in understanding usb concept and serial port.
I think any usb device assigned to a serial port e.g usb webcam.
I attach a usb webcam to my computer and QSerialPortInfo did not find it also.
I ran a command for my mouse :
@ udevadm info --name=/dev/input/mouse0 -aUdevadm info starts with the device specified by the devpath and then
walks up the chain of parent devices. It prints for every device
found, all possible attributes in the udev rules key format.
A rule to match, can be composed by the attributes of the device
and the attributes from one single parent device.looking at device '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/input/input5/mouse0':
KERNEL=="mouse0"
SUBSYSTEM=="input"
DRIVER==""looking at parent device '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/input/input5':
KERNELS=="input5"
SUBSYSTEMS=="input"
DRIVERS==""
ATTRS{name}=="A4Tech PS/2+USB Mouse"
ATTRS{phys}=="usb-0000:00:1a.0-1.1/input0"
ATTRS{uniq}==""
ATTRS{properties}=="0"looking at parent device '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0':
KERNELS=="1-1.1:1.0"
SUBSYSTEMS=="usb"
DRIVERS=="usbhid"
ATTRS{bInterfaceNumber}=="00"
ATTRS{bAlternateSetting}==" 0"
ATTRS{bNumEndpoints}=="01"
ATTRS{bInterfaceClass}=="03"
ATTRS{bInterfaceSubClass}=="01"
ATTRS{bInterfaceProtocol}=="02"
ATTRS{supports_autosuspend}=="1"looking at parent device '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1':
KERNELS=="1-1.1"
SUBSYSTEMS=="usb"
DRIVERS=="usb"
ATTRS{configuration}=="HID-Compliant Mouse"
ATTRS{bNumInterfaces}==" 1"
ATTRS{bConfigurationValue}=="1"
ATTRS{bmAttributes}=="a0"
ATTRS{bMaxPower}=="100mA"
ATTRS{urbnum}=="174621"
ATTRS{idVendor}=="09da"
ATTRS{idProduct}=="000a"
ATTRS{bcdDevice}=="0002"
ATTRS{bDeviceClass}=="00"
ATTRS{bDeviceSubClass}=="00"
ATTRS{bDeviceProtocol}=="00"
ATTRS{bNumConfigurations}=="1"
ATTRS{bMaxPacketSize0}=="8"
ATTRS{speed}=="1.5"
ATTRS{busnum}=="1"
ATTRS{devnum}=="3"
ATTRS{devpath}=="1.1"
ATTRS{version}==" 1.10"
ATTRS{maxchild}=="0"
ATTRS{quirks}=="0x0"
ATTRS{avoid_reset_quirk}=="0"
ATTRS{authorized}=="1"
ATTRS{manufacturer}=="A4Tech"
ATTRS{product}=="PS/2+USB Mouse"looking at parent device '/devices/pci0000:00/0000:00:1a.0/usb1/1-1':
KERNELS=="1-1"
SUBSYSTEMS=="usb"
DRIVERS=="usb"
ATTRS{configuration}==""
ATTRS{bNumInterfaces}==" 1"
ATTRS{bConfigurationValue}=="1"
ATTRS{bmAttributes}=="e0"
ATTRS{bMaxPower}==" 0mA"
ATTRS{urbnum}=="77"
ATTRS{idVendor}=="8087"
ATTRS{idProduct}=="0020"
ATTRS{bcdDevice}=="0000"
ATTRS{bDeviceClass}=="09"
ATTRS{bDeviceSubClass}=="00"
ATTRS{bDeviceProtocol}=="01"
ATTRS{bNumConfigurations}=="1"
ATTRS{bMaxPacketSize0}=="64"
ATTRS{speed}=="480"
ATTRS{busnum}=="1"
ATTRS{devnum}=="2"
ATTRS{devpath}=="1"
ATTRS{version}==" 2.00"
ATTRS{maxchild}=="6"
ATTRS{quirks}=="0x0"
ATTRS{avoid_reset_quirk}=="0"
ATTRS{authorized}=="1"looking at parent device '/devices/pci0000:00/0000:00:1a.0/usb1':
KERNELS=="usb1"
SUBSYSTEMS=="usb"
DRIVERS=="usb"
ATTRS{configuration}==""
ATTRS{bNumInterfaces}==" 1"
ATTRS{bConfigurationValue}=="1"
ATTRS{bmAttributes}=="e0"
ATTRS{bMaxPower}==" 0mA"
ATTRS{urbnum}=="25"
ATTRS{idVendor}=="1d6b"
ATTRS{idProduct}=="0002"
ATTRS{bcdDevice}=="0303"
ATTRS{bDeviceClass}=="09"
ATTRS{bDeviceSubClass}=="00"
ATTRS{bDeviceProtocol}=="00"
ATTRS{bNumConfigurations}=="1"
ATTRS{bMaxPacketSize0}=="64"
ATTRS{speed}=="480"
ATTRS{busnum}=="1"
ATTRS{devnum}=="1"
ATTRS{devpath}=="0"
ATTRS{version}==" 2.00"
ATTRS{maxchild}=="2"
ATTRS{quirks}=="0x0"
ATTRS{avoid_reset_quirk}=="0"
ATTRS{authorized}=="1"
ATTRS{manufacturer}=="Linux 3.3.4-5.fc17.x86_64 ehci_hcd"
ATTRS{product}=="EHCI Host Controller"
ATTRS{serial}=="0000:00:1a.0"
ATTRS{authorized_default}=="1"looking at parent device '/devices/pci0000:00/0000:00:1a.0':
KERNELS=="0000:00:1a.0"
SUBSYSTEMS=="pci"
DRIVERS=="ehci_hcd"
ATTRS{vendor}=="0x8086"
ATTRS{device}=="0x3b3c"
ATTRS{subsystem_vendor}=="0x1028"
ATTRS{subsystem_device}=="0x0447"
ATTRS{class}=="0x0c0320"
ATTRS{irq}=="16"
ATTRS{local_cpus}=="00000000,0000000f"
ATTRS{local_cpulist}=="0-3"
ATTRS{numa_node}=="-1"
ATTRS{dma_mask_bits}=="32"
ATTRS{consistent_dma_mask_bits}=="32"
ATTRS{broken_parity_status}=="0"
ATTRS{msi_bus}==""
ATTRS{companion}==""
ATTRS{uframe_periodic_max}=="100"looking at parent device '/devices/pci0000:00':
KERNELS=="pci0000:00"
SUBSYSTEMS==""
DRIVERS==""
@ -
bq. You say USB mouse is not a serial port?
Yes. The USB mouse it is an "input" class device, not an "tty" class device (i.e. not an serial port).
bq. I run a virtual serial port using socat and again QSerialPortInfo did not find.
You should do modifications in source code (as I say before) and then your /dev/ttyS0 device will listed.
bq. Maybe I have problem in understanding usb concept and serial port.
Yes, it is. :)
[quote]
I think any usb device assigned to a serial port e.g usb webcam.
I attach a usb webcam to my computer and QSerialPortInfo did not find it also.
[/quote]Sorry, you are wrong. :)
In any case, your PC's has not any serial ports. You has only a few "faked" /dev/ttyS0-S3 (maybe up to ttyS14) serial ports. It is normal... You can read more about serial ports e.g. "here":http://www.tldp.org/HOWTO/Serial-HOWTO-10.html.
-
[quote author="jmimi" date="1388572677"]You say USB mouse is not a serial port?[/quote]Hi,
USB = "Universal Serial Bus", not "Serial Port". This is what most serial ports look like: http://en.wikipedia.org/wiki/File:Serial_port.jpg
The Serial Port is a very old technology. They can still be found in embedded systems and industrial systems, but modern PCs don't supply them any more.
-
[quote author="jmimi" date="1388575219"]I know RS232 is a serial port and I think usb is serial too.[/quote]Yes, USB and RS-232 communications are both serial, but their protocols are VERY different:
- Serial port: http://en.wikipedia.org/wiki/RS-232#Signals
- USB: http://en.wikipedia.org/wiki/USB#Communication
Nowadays, when people say "serial port", they mean "RS-232". Even though data is transmitted through USB cables serially, USB does not use the RS-232 standard. Therefore, USB ports are not considered serial ports.
From the "Qt documentation":http://qt-project.org/doc/qt-5/topics-network-connectivity.html#serial-port-communication:
"The Qt Serial Port module provides a C++ API for communicating through serial ports, using the RS-232 standard. It works with physical ports and also with drivers that emulate these ports. Examples of serial port emulators include virtual COM ports, com0com emulators, and the Bluetooth SPP."
-
Thanks you JKSH
I should read more.
I create a virtual com port using socat according below
@$ socat -d -d pty,raw,echo=0, pty,raw,echo=02014/01/01 16:03:58 socat[10509] N PTY is /dev/pts/4
2014/01/01 16:03:58 socat[10509] N PTY is /dev/pts/5
2014/01/01 16:03:58 socat[10509] N starting data transfer loop with FDs [3,3] and [5,5]@
But QSerialPortInfo did not find for me. According to documentation you linked, it should be happened but it didn`t.
So I willchange the source code according to kuzulis said and test again.
I do not have the device right now. I want to develop software without it and will test with the device actually. communication with device is part of my software. So I need to create a virtual com port and test with it. -
socat creates symlink, but QSerialPortInfo does not care about symlinks:
https://code.woboq.org/qt5/qtserialport/src/serialport/qserialportinfo_unix.cpp.html#91 -
socat creates symlink, but QSerialPortInfo does not care about symlinks:
https://code.woboq.org/qt5/qtserialport/src/serialport/qserialportinfo_unix.cpp.html#91@huseyinkozan Please create a report at bugreports.qt.io for this. This forum is not the right place to discuss if the behavior is correct or not.
And @kuzulis, you might be interested in this.
-
Yes, QSPI ignores the socat's symlinks, because it is not a serial ports at all. It is not a bug. If you want to use a virtual serial ports on linux, please use the tty0tty kernel module.
